C# Discussion Boards - CodeProject

9-Dec-08 1:06

hello all

i treid the code below but nothing happens....

//in button write

serialPort1.PortName = "COM1";
serialPort1.BaudRate = 9600;
serialPort1.DataBits = 8;
serialPort1.Parity = Parity.None;
serialPort1.StopBits = StopBits.One;
serialPort1.Open();
serialPort1.Write("A");
serialPort1.Close();

// in Button Read
serialPort1.Open();
textBox1.Text = serialPort1.ReadLine();

Giorgi Dalakishvili9-Dec-08 1:10

Giorgi Dalakishvili

9-Dec-08 1:10

You asked the same question 20 minutes ago. Why are you double-posting? It's rude. You'd better read the documentation instead of double posting.

Giorgi Dalakishvili

#region signature
My Articles

Asynchronous Registry Notification Using Strongly-typed WMI Classes in .NET [^]

My blog
#endregion

Simon P Stevens9-Dec-08 1:11

9-Dec-08 1:11

Like I said below:

What are you expecting to happen? You can't just write "A" to a serial port and then expect to read it back.

You need to have some hardware connected to the serial port that either responds to data, or transmits data in.

(Stop reposting questions, you'll only annoy everyone and get the same answers)

Simon

TJS4u9-Dec-08 1:18

9-Dec-08 1:18

hello Simon Stevens

my requirement is to connect a microcontrolelr to the serial port .

i tried this to see if data is in the buffer ... then it can't be read back

Thanks

Simon P Stevens9-Dec-08 1:27

9-Dec-08 1:27

You need to read your micro controllers docs.

Simon

TJS4u9-Dec-08 1:38

9-Dec-08 1:38

hello Simon Stevens

first i need to download some data to the microcontroller from my application ... the microcontroller is connected to the Serial port.

When the Microcontroller receives the data it executes its and it returns some data.. at this time i expect this data be in the port and need to read ir from the serial port

i await for u r suggestions on this

Thanks

Eddy Vluggen9-Dec-08 1:21

9-Dec-08 1:21

TJS4u wrote:
i treid the code below but nothing happens....

That's incorrect, as something did happen. Either you didn't see it happen, or you didn't understand what happens.

The serial port doesn't "remember" that you sent an "A", since there is no memory attached to the serial port. Did you get an exception, or did the serial-port just 'eat' the information you sent?

Same problem with reading from the serial port. If there isn't anything attached and sending messages, then there won't be anything to read from the port.

Your best option would be going out to buy a "null-modem cable", or something that can echo the signals from the serial port.

I wish you lots of luck, as you are going to need it Frown | :(

TJS4u9-Dec-08 1:34

9-Dec-08 1:34

hello Eddy Vluggen

i am new to C#.. so asking such questions...

the code is executing and when it enters the line
string line=...................

the system hangs

wht to do next
How can i be sure that the port is enabled and data has been send to the port...
OR if i connect a device will that respond to the code i have written

i await u r suggestions

Thanks

Eddy Vluggen9-Dec-08 1:47

9-Dec-08 1:47

TJS4u wrote:
the system hangs

No, it's not hanging, but waiting. Waiting for someone to send a carriage-return + linefeed to the serial port. In other words, the system is reading from the serial port, and will continue reading, until someone sends an "enter" to the serial port.

TJS4u wrote:
How can i be sure that the port is enabled and data has been send to the port...

Make yourself a cable that echo's everything.

TJS4u wrote:
if i connect a device will that respond to the code i have written

The device doesn't know about your code. Your code will have to speak to the device in a way that the device itself understands. Various devices use the serial port in different ways. Your micrologger will have some examples on this.

TJS4u9-Dec-08 1:56

9-Dec-08 1:56

hello Eddy Vluggen

Thanks for u r reply

still some things makes confusing///

i have written

string line = serialPort1.ReadLine();

At this point will the variable line stores the value from the port???

if a device is connected and it has some thing to return

Thanks

Eddy Vluggen9-Dec-08 3:11

9-Dec-08 3:11

TJS4u wrote:

string line = serialPort1.ReadLine();

At this point will the variable line stores the value from the port???

At that point the computer will *wait*, until a device sends an "enter". It will keep stuffing all data into the "line" variable, until it receives the enter-character.

Does your logger send a return-character when it is done sending data?

TJS4u9-Dec-08 3:19

9-Dec-08 3:19

hello Eddy

the microcontoller will get the code which is downloaded to it thru the port and it will execute

after execution the result is send to the application thru the serial port from the microcontroller

Thanks

Eddy Vluggen9-Dec-08 3:25

9-Dec-08 3:25

TJS4u wrote:
the microcontoller will get the code which is downloaded to it thru the port and it will execute

You're sending "code" to the controller? I'm afraid I don't understand what you're saying here, can you give an example of the codes that you wanna send?

TJS4u wrote:
after execution the result is send to the application thru the serial port from the microcontroller

..and the ReadLine() method will "hang" until the microcontroller sends this "enter"-character. I bet that the logger doesn't send it Smile | :)

It works if you remove that line, doesn't it?

create slidable form [modified]

Luc Pattyn9-Dec-08 1:59

Luc Pattyn

9-Dec-08 1:59

Hi,

It is my impression this project is way beyond your current reach. Nevertheless here are some facts:

1.
transmit and receive channels are (almost) completely independent: there is a wire in each direction, there is separate electronics, separate data buffers, and different methods to call.
The only link exists inside the serial driver when software dataflow is used (XON/XOFF).
2.
whatever gets sent through a serial port is gone in a couple of micro- or milliseconds, you can't read it back; you can (if things go well) find the data at the target hardware after that delay.

Some suggestions:
1.
if all is new to you (C#, serial ports, microcontroller) you have zero probability to get it working by just setting it all up and hope for the best. You MUST go step by step, debug each step completely before taking the next step.
2.
The first step should be one of these (in increasing level of difficulty):
2a. use two PC's (I'll call them master and target) connect them through a serial cable WITH A NULL MODEM (which switches transmit and receive lines); run a terminal emulator (HyperTerminal, whatever) on the target PC, so you make it emulate your microcontroller by reading the emulator display and typing keys when appropriate. And run your own code on the master PC. Now you can first debug transmission: your program writing, the emulator showing what comes in; then you can tackle the receive side (with buffers, events, etc).
2b. you could try the same on a single PC (using two serial ports, connected with again a NULL MODEM); it is much less comfortable though.
2c. you don't even need real serial ports and a null modem cable, you can use a VIRTUAL NULL MODEM
(Google for com0com).
3. If all this works, you could try to use the microcontroller. If that one needs a program download, you'd better won't need its serial port for that, since it has not been debugged yet,
so it will not work initially.

Good luck.

Luc Pattyn [Forum Guidelines] [My Articles]

Fixturized forever. Confused | :confused:

Member 44132839-Dec-08 0:47

Member 4413283

9-Dec-08 0:47

how i open my form as open in .net by mouseover on properties,solution explorer etc.

i want to open form as when u add new form in .net in solution explorer i want create my strip and on a tab name say print on mouse over a form slide and show and on mouse out it slide again to left or right. i want to do in my mdi form

thanks.
send solution on sharma_diw@hotmail.com

modified on Tuesday, December 9, 2008 6:56 AM

Re: create slidable form

Simon P Stevens9-Dec-08 0:53

How to Read and Write to Serial Port using C#

9-Dec-08 0:53

You open a form by calling either .Show() or .ShowDialog() on the form object.

If you want to do it in the mouse over, you must add an event handler to the mouse over event, and show the new form from there.

Simon

Re: create slidable form

Brij9-Dec-08 0:57

Brij

9-Dec-08 0:57

Add a event on Mouseover that should open the form

Cheers!!
Brij

TJS4u9-Dec-08 0:46

Re: How to Read and Write to Serial Port using C#

9-Dec-08 0:46

hello all

I want to write some data to a serial port and Read from the Port the data and display in a textbox ...

how can i do this

Simon P Stevens9-Dec-08 0:51

Re: How to Read and Write to Serial Port using C#

9-Dec-08 0:51

Did you even try google?

I found this in about 2 seconds: MSDN Serial Port[^]

Simon

TJS4u9-Dec-08 0:56