C / C++ / MFC

cv_k3n15-Aug-06 21:39

cv_k3n

15-Aug-06 21:39

Sorry but i don't quite get your explanation for my second question. What i want to do is to call another function when my thread finishes whatever it was doing. Hope you can explain it to me again. Thanks.

Hamid_RT15-Aug-06 23:54

15-Aug-06 23:54

when you create a thread how do you finish it.TerminateThread if you use from this function then you can use GetExitCodeThread
that retrieves status from thread and you can check status returned that is STILL_ACTIVE or no
Is this your question?

WhiteSky

cv_k3n16-Aug-06 2:04

cv_k3n

16-Aug-06 2:04

Thanks for your help... i've tried it but i'm not sure if its right.

Does this look right to you:

TerminateThread(myWorkerThread,GetExitCodeThread(myWorkerThread,0));

Another Question:

Assuming the code below,

MyDialog::MyThread()<br />
{<br />
int i = 0;<br />
while (i < 5000)<br />
     i++;<br />
}

I understand that a worker thread is not supposed to touch a GUI object. Is there a way to terminate this thread(when it completes, ie i = 5000) and call another function that can actually change some GUI variables?

Thank you so much for your help.

Hamid_RT16-Aug-06 4:33

16-Aug-06 4:33

one thing that i think its important a thread remain in system until you terminate it and close all handle with CloseHandle

(1)TerminateThread is for finish a thread when you call this function for get exit value if thread is active you get STILL_ACTIVE else you get value that is in second parameter from this function dxExitCode

(2)
Hope I understood your question
It seems that its depend to previous your questions(check when i=5000 finish thread and load your function) is your question?
(you can use from WM_TIMER instead a while(5000) when you need to 5000 you can set SetTimer(...) and when i=5000 in wm_timer you can Kill timer with killTimer and run another function )
if its your answer i am glad if its not your answer so

you can ask and if i can i answer to you

WhiteSky

checksum [modified]

thathvamsi13-Aug-06 18:38

thathvamsi

13-Aug-06 18:38

Hi all,
Iam having a checksum algo implemented in my code.
The Pc receives a packet from microcontroller and then does this as a check:

for(i=0;i < max_length-1;i++)<br />
{<br />
checksum ^= recd_buf[i];<br />
}

then this checksum is compared with the last member fo the received packet which has the checksum sent from microcontroller.

if(checksum != recd_buf[max_length-1])<br />
{<br />
"bad packet"<br />
}

but i always get the values to be not equal. By printing out the received packet details, they are all correct.
there s no error on the microcontroller end.
There is error in the calcualtion of checksum at the Pc end (the code shown above).

Can anyone help? I know there are various checksum algos available. but i want to find out the bug/error in this.
thanks in advance.

-- modified at 0:39 Monday 14th August, 2006

tanvon malik13-Aug-06 18:54

tanvon malik

13-Aug-06 18:54

look here
if(checksum != recd_buf[max_length-1])
{
"bad packet"
}

do you think in " recd_buf[max_length-1]) "
the "max_length-1 " is ok. why donot you compare with
"max_length " . Because in first "for loop " your iterator "i" starts from " 0 " but at this time you are just checking maximum length.

as long I think
if(checksum != recd_buf[max_length])
{
"bad packet"
}

Tanvon

the brain behind ...

Steve Echols13-Aug-06 19:23

Steve Echols

13-Aug-06 19:23

I think his loop is correct, because you usually don't include the check sum value in the check sum algo, hence the < max_length - 1 in the loop control. If you did recd_buf[max_length], that would be out of bounds, since it's zero based.

Thinking about it more, maybe the checksum should be part of the algo, maybe try i < max_length, instead of max_length - 1, and see if that works.

I've seen some other algorithms as well, but try that first.

- S
50 cups of coffee and you know it's on!

Michael Dunn13-Aug-06 19:29

Michael Dunn

13-Aug-06 19:29

Is checksum initialized properly?
What are your data types? When using the bitwise operators, all types should be unsigned. You may be getting bit by sign-extension or some other result of integral promotion.

--Mike--
Visual C++ MVP Cool | :cool:

LINKS~! Ericahist | PimpFish | CP SearchBar v3.0 | C++ Forum FAQ

thathvamsi13-Aug-06 19:45

thathvamsi

13-Aug-06 19:45

Hi,
I initialise checksum to zero everytime before calculating it.
Also, the data types are of signed16 or short and few are of float values.
But the received buffer is declared as char type and all the values are stored as 8 bit values in recd_buf[0] to recd_buf[max_length-1].

from the microcontroller end, the checksum is calcualted in a similar way and the checksum value is stored in the last position ie., sent_buf[max_length-1].
and in the PC end, the checksum is calculated the same way,(as in my previous message),
and the calcualted checkum is compared with the value that was sent as the last member of the packet from microcontroller.

Does this info help you? Any ideas/ suggestions?

Re: checksum -works now

thathvamsi14-Aug-06 16:26

thathvamsi

14-Aug-06 16:26

hey all,
Thanks all for ur help.
I could get my algo going.
1. I had the checksum declared as char-- but now changed it to unsigned char.
2. the next thing was:
I was comparing the checksum value with the last member of the received packet array (where the array was declared to be signed char)
I created a temporary unsigned char variable and copied the last member of the array (checksum from microcontroller) to it.
Then used this temporary variable for comparing with the checksum calculated in Pc.
It works perfect.
It was basically signed/unsigned datatype problem..

Thanks to all again for ur help.

ProcessShellCommand problem in release mode

Archyami13-Aug-06 20:33

Archyami

13-Aug-06 20:33

Have you tried to have the message sent with length equal to max_length including the checksum?

if(the length of the message is not equal to max_length)
{
if(checksum generated to array[real_length-1])
wrong;
else // checksum generated to array[max_length-1]
{
wrong;
// before and after transmission, index from real_length to max_length-1 =
// unknown values
}
}
else
must be correct

NorGUI13-Aug-06 18:08

NorGUI

13-Aug-06 18:08

Hello,
After switching to release mode, the ProcessShellCommand show me a messagebox that say "error to build a empty document" and the fonction return false. I do not understand because my application was running without any problem before and now I get this problem.

What can I try to solve my problem.

Thank you

AutreChien

How to print the text in the new line of a multi line edit box .

VCSharp00713-Aug-06 18:05

VCSharp007

13-Aug-06 18:05

Hi,
I tried pEdit->SetWindowText("/n"); but a junk character is displayed instead of going to new line .
Plz help.
thanx in advance

Re: How to print the text in the new line of a multi line edit box . [modified]

bob1697213-Aug-06 18:26

bob16972

13-Aug-06 18:26

try "\r\n"

also make sure your edit control style is ES_MULTILINE

Re: How to print the text in the new line of a multi line edit box .

VCSharp00713-Aug-06 20:44

VCSharp007

13-Aug-06 20:44

Yeah.
It worked.
Thanx once again.

Re: How to print the text in the new line of a multi line edit box .

Hamid_RT13-Aug-06 21:37

about system32\netshell.dll

13-Aug-06 21:37

See here[^] maybe it is some helpful to you

WhiteSky

diat13-Aug-06 18:03

diat

13-Aug-06 18:03

what functions does netshell.dll include?
what parameters do they have?
And, thanks.

Re: about system32\netshell.dll [modified]

A_Fa13-Aug-06 19:11

A_Fa

13-Aug-06 19:11

DllCanUnloadNow
DllGetClassObject
DllRegisterServer
DllUnregisterServer
NcFreeNetconProperties
NcIsValidConnectionName
HrLaunchNetworkOptionalComponents
HrCreateDesktopIcon
HrLaunchConnection
HrRenameConnection
InvokeDunFile
DoInitialCleanup
NetSetupRequestWizardPages
NetSetupFinishInstall
NetSetupAddRasConnection
HrDetectLegacyNetCards
HrUninitLegacyNetCardDetection
HrOemUpgrade
HrGetAnswerFileParametersForNetCard
HrGetInstanceGuidOfPreNT5NetCardInstance
NetSetupSetProgressCallback
NetSetupInstallSoftware

Open netshell.dll with Dependency Software !

details, please

diat16-Aug-06 17:53

diat

16-Aug-06 17:53

I just want to how to use them. And, the parameters.

Re: details, please

A_Fa16-Aug-06 20:03

A_Fa

16-Aug-06 20:03

this is example how to use func in dll :

<br />
# define LWA_COLORKEY 1<br />
# define LWA_ALPHA 2<br />
# define WS_EX_LAYERED 0x80000<br />
	HWND hWnd=this->m_hWnd;<br />
    typedef DWORD (WINAPI *PSLWA)(HWND, DWORD, BYTE, DWORD);<br />
	PSLWA pSetLayeredWindowAttributes;<br />
	HMODULE hDLL = LoadLibrary ("user32");<br />
	pSetLayeredWindowAttributes = (PSLWA) GetProcAddress(hDLL,"SetLayeredWindowAttributes");<br />
	/*<br />
	* Make the windows a layered window<br />
	* /<br />
	if (pSetLayeredWindowAttributes != NULL) <br />
	{<br />
		SetWindowLong (hWnd, GWL_EXSTYLE, GetWindowLong<br />
		(hWnd, GWL_EXSTYLE) |WS_EX_LAYERED/*|WS_EX_TOOLWINDOW* / );<br />
	}<br />
<br />
	pSetLayeredWindowAttributes (hWnd, 250, 255, LWA_COLORKEY|LWA_ALPHA);<br />
<br />
<br />
	FreeLibrary(hDLL);	<br />
<br />

For parameter of functions refer to MSDN

Re: about system32\netshell.dll

Hamid_RT13-Aug-06 21:35

Can a function call a afx_msg function??? [modified]

13-Aug-06 21:35

diat wrote:
what functions does netshell.dll include?
what parameters do they have?

What do you need exactly?

WhiteSky

mimimimilaw13-Aug-06 17:33

mimimimilaw

13-Aug-06 17:33

afx_msg void OnSize(UINT nID, int intWidth, int intHeight);

This function to change the position of all items on a dialog. Can i call this function by another function to redraw the dialog? If not, does it have another method to re-posit all items?
Thx

Another Questions:
How to set Picture control from invisible to visible?
how to get the width and the heigth of a dialog?

-- modified at 0:13 Monday 14th August, 2006

Re: Can a function call a afx_msg function???

Hamid_RT13-Aug-06 19:33