|
The desired behaviour you describe is exactly what ActiveSync is doing at my workstation. So probably your devices run on a different platform than mine.?
My devices run Windows CE 3.0, Windows CE.NET 4.1 and Windows CE.NET 4.2.
I connect these devices either using one of the serial ports or USB.
So in ActiveSync I choose which COM port that I will be using, and I check the checkbox to accept USB connections, further in the Connection Settings of ActiveSync I have selected
"This computer is connected to:" to Automatic
And I have checked the checkbox: "Open ActiveSync when my device connects"
That`s it from the PC side, on my handhelds I just go to the
control pannel -> PC Connection and in there I enable direct connections
That`s it. Now whenever I connect the device the PC immediatly recognizes the connection attempt and connects to the device.
Ah, one thing, the connection doesn`t work if I boot my device while it is connected to the PC. So I have to connect the device to the PC while the device is allready up and running. Or if it was allready connected when booting just break the physical connection and re-establish it.
I never access the ActiveSync program directly except when I wish to change the serial port to which it should poll for devices.
I hope this gives might give you an idea as to what may cause your problem.
Regards,
Davy
|
|
|
|
|
My device has Windows CE .NET 4.2 installed, but in PC Connection I have no option to enable direct connections. I can just select which comm port to use along with the speed. When I disconnect the serial cable and reconnect it, I have to manually start PCLink again to connect to the desktop.
|
|
|
|
|
I need to know the Ethernet Permanent Mac Address
and I would like to know how to detect if a ethernet
card is :
1) removable (tipical of laptop) or fixed (on the bus)
2) on board on a dockin station
3) avoid mac addres like 00-53-45-00-00-00 (wireless
card??)
Im work with devstudio C++ 7.1
Can you help me ?its very urgent
Thank you a lot in advance for any suggestion/help
Mario
|
|
|
|
|
Hi all,
I am experiencing a problem with a windows ce terminal. The terminal is connected to a wireless network. All seems fine, and can ping the needed servers and workstation. However, when i try to make a connection through net use * \\192.168.11.113\bginfo, or any other share on any server/workstation it fails with the error message: command failed: status 53.
Does anyone have a clue? It can't be the username / password combination because we have tried that also.
Any help would be very much appreciated.
Rolf
|
|
|
|
|
Hi All
I am using DataSet from Oracle and serialized it XML file. Using the Same file in Pocket PC with .NET Compact Framework C# Application.
My Problem is that whenever there is a change/update in any row(field) i want to update the same in the XML File. If i use the function to write to xml it writes the complete DataSet of PPC onto the XML which takes hell of a time as there is 300 Records. Where as i need to know if there is anyway that i can update only the part of XML which has been effected in DataSet
Rakesh Salian
|
|
|
|
|
I would try one of the follow :-
1. Thats the kind of thing I would be inclined the use a memory mapped file for, I don't know how the Windows CE MSXML would react to that, I have studied/used that SDK in a while, but having the whole xml file in memory is going to help.
2. Another good alternative would be to encapsulate all that business logic in a seperate threads, using a queue of requests/write to read and write to the DOM, therefore insulating the GUI from any performance problems the XML end of things is having. This would tricky to get right.
3. I would also try and normal the dataset to the nth degree, at 300 records you _must_ have alot of repetition there, lose it, do _anything_ to get that dataset smaller.
Regards
Ray
"Je Suis Mort De Rire"
Blogging @ Keratoconus Watch
|
|
|
|
|
hello ...
I tried to use NotifyIcon class from this article http://msdn.microsoft.com/library/default.asp?url=/library/en-us/dnnetcomp/html/messagewindow.asp but the odd thing is that it makes an icon but the icon is invisible.I know that it`s there becose I`ve put a Click event on it + MessageBox.Show("111"); and the message box appears.
I tried both :
String szPath = Assembly.GetExecutingAssembly().GetModules()[0].FullyQualifiedName;
ExtractIconEx(szpath, 0, 0,ref hIcon, 1);
and
hIcon = LoadIcon(GetModuleHandle(null), "Icon1");
but the result is the same (the icon is 16x16).
Can someone give another solution?
I am using the Windows CE .NET Emulator that ships in VS.NET 2003.
Eusebiu
C#.NET Developer
|
|
|
|
|
Greetings:
I am programming a Fujitsu Siemens LOOX 720 PDA running Windows Mobile 2003 2nd Edition. I am using Visual Studio 2003 and programming in C# under the "Smart Device" configuration.
I have hit a brick wall:
Every time I set come to a breakpoint that I have set, mosy computer disconnects from my PDA. The message box that comes up says:
"The remote connection to the device has been lost. Please verify the device connection and restart debugging."
This is happening every single time I come to ANY breakpoint! I am trying to debug some problems but I can't get anything done!
Thanks in advance to anyone who responds.
Mark
|
|
|
|
|
Hi,
What is the version of the emulator you are using? It seems to be a problem in with the emulator 5.3.0.26 when used with Visual Studion 2003
With the emulator 4.2.0.20 it works as expected. Incase, it dosen't work, Check your Emulator settings.
Thanks,
Kishore Gaddam.
|
|
|
|
|
Hi Kishore, thanks for your response.
I will check and let you know.
Mark
|
|
|
|
|
hard reset the device ...
Regards
Ray
"Je Suis Mort De Rire"
Blogging @ Keratoconus Watch
|
|
|
|
|
I am developing an application using 802.11b wireless on a CE.NET 4.2 device using C# and .NET CF1. When I go out of range of the wireless base station, if I get back in range before the connection on the device gives up retrying, I can regain a connection to my application server. But if the wireless connection stops trying before I get back in range, my application will consistently fail to connect. The only way is to manually go back and renew the connection in the IP settings. Something I don't want the end user to have to do.
Can anybody give me some advice as to how I refresh the connection settings from within my application, or how I can check the status of the adapter?
Many thanks
|
|
|
|
|
I have a issue with the PPC installation using cab wizard, any idea how to over come this. I need to overwrite the installtions, with out asking for user confirmation in the sucessive installations, how to do this.
Brief of what I have done is below.
I have created 8 cab files and I have given the overwrite option in the .inf file like
[Files.XYZ]
File1.cfg,,,0
File2.cfg,,,0
Finally my batch file contains below line for isntallation.
CEAppMgr.exe ".\install1.ini" ".\install2.ini" ".\install3.ini" ".\install4.ini" ".\install5.ini" ".\install6.ini" ".\install7.ini" ".\install8.ini"
I want to get rid of app manager asking '...already installed.Do you want re-install/upgrade?'.
Thanks,
Krishnan
|
|
|
|
|
I wish to implement a application to make translation between chinese word to english word in pocket pc. It will allow user write the chinese word in pocket pc then send remotely by .net compact framework(xml web service) to the remote server. Is the pocket pc itself support write foreign language (chinese word) and can xml web service send chinese word to the remote server from pocket pc?
|
|
|
|
|
Yes, Pocket PC supports multi language implementation but i doubt if Chinese is included in the list of supported languages. Well, incase if Chinese is not supported, then i guess, you can try some of the free libraries that give Internationalization support for Chinese language.
Thanks,
Kishore
|
|
|
|
|
I wish to implement a chat room that use between PDA (pocket pc) and desktop pc using C#. Is it any idea to implement this? XML web service can implement this? or any other suggestion for it?
|
|
|
|
|
hallo
i loaded a xml file to datagrid. now i like to save this datagrid to my table called maf1 which is in sdf database.
beagle 01
|
|
|
|
|
How can i install & run j2me midlet on Windows Mobile 5?
|
|
|
|
|
Hello All,
I'm trying to develop a mobile application which gives the current price of a particular share(which changes fequently). So i need to get the new price of that share whenever it changes. I have tried to REFRESH the form so that pageload works again & we can fetch the changed price from the database ---but in vain!
I tried this too:-
<acme:TimerFormVB Title="Need a title?" runat="server" id="Form1" removed="Form_OnTimer" Delay="5">
</acme:TimerFormVB>
but it doesn't work. What is this , I got the above code from the net. Is this some set of controls.
Iam using Visual Studio .Net 2003
Can anyone suggest a solution.
Regards,
jeeva
|
|
|
|
|
Need to convert a shockwave flash video file into some mobile compatible video format (most probably 3gp). If anyone has any open source about this please send me.
Muhammad Kashif
|
|
|
|
|
i want to develop mobile web site in visual studio 2005 but i cant get the mobile web template ,plz help me
i am a student of MSc computer science at quaid-e-azam university islamabad pakistan , my logo is "help to all"
|
|
|
|
|
Hi!
I am developping a mobile application using CF 2.0 and VS 2005. I want to be able to use some features of Pocket Word.
How to add a reference to Pocket Word (like it is possible to do with Framework 2.0 and the COM technology) so that I can use it in my application?
Thks in advance!
Appstmd
http://www.atlence.com
|
|
|
|
|
Hi,
Celljump are looking to employ 1-2 people with experience within mobile/handset communication.
Celljump are a stable company and have an clear desire to be listed on the London AIM stock market during 2006/2007. The process for this has been started.
The following qualifications are desirable:
"Computer Science" or similar background from an accredited
institution - may be compensated by exceptional practical experience
Extensive programming experience in C++
Experience in working with mobile phones and/or PDAs at a
software level
Practical experience with programming microcontrollers, in
particular the ATMEL chipset a necessity
Experience of implementing IrDA OBEX protocols highly desirable
Knowledge of USB protocols a necessity
Good working knowledge of English
A structured, motivated self-started with evidence of delivering
complex programming tasks on time in full
We are also looking for development companies that can take on larger projects that we are going to outsource.
For more information, please contact one of the following persons:
Mr. Andreas Eriksson
andreas@celljump.net
+46 70 555 61 65
Mr. Josef Widstroem
josef@celljump.net
+46 735 333 555
Best Regards
Andreas Eriksson
|
|
|
|
|
hi,
would really appreciate if someone can explain how i can connect and use external keyboard for mobile device using wm2005. there are programs like SOTI but i would like to program it on my own. will really appreciate if someone can explain how it could be possible.
|
|
|
|
|
how can i access wap by mobile device.
Shamsh Tabrij
|
|
|
|