You will also have a problem with the first two of your format strings when the month and day are both less than 13.
Actually, I did have that problem when I was using TryParse and using locale.
What I've done is following. For each datetime field, I've added custom attribute that spells out which format is most likely to be most appropriate for that particular field. This way, on some fields, I do instruct it to read it as dd/mm and on others I do ask it to read mm/dd.
I would address this a different way, assuming each stream is identifiable and is internally consistent, I would register a format for each source.
They are consistent in a sense that if mm was before dd, it does seem to remain that way ... but I'd be in trouble if I assume that it will always be slash / between characters. Sometimes it is dash or space too. So, I weed out all unwanted characters using String.Replace and replace them with what slashes as I have
'em on my format string before even attempting to parse the date.
Further, I do have custom attribute defined for each and every date/time field which essentially leads to one of the eight format strings as "tryFirstFormat". So, yes! I do have one format registered for each field although I know that expecting it to remain consistent is a bit-too-much at this point in time....
In the code, before the loop, I use parseExact to parse the date. Naturally that too is in its own try-catch block. Only if that fails, code will enter the loop.
I did not post all of the above code assuming that more code will confuse people and felt that it was not relevant to problem. But it seems from the early responses that partial code is confusing ppl more.
I usually don't comment on a question like this, when the OP has a made a comment of the form "it works," in response to a solution.
But, I'd like to note that, imho, Eddie Vluggen asked what I think is the critical question here:
"The name of a form-object (name property) or the name of the forms' class? In other words, does the form already exist that you're looking for, or are you showing a new instance of that form?"
To which the OP responded:
"Form already exists in the application.
form name is in a string.
how do i open that form."
The code shown in the response by Jean Brandelero will create a new instance of the Form based on its class-name. And, perhaps, that is exactly what the OP wanted.
But, it also seems possible the OP does not want to create a new instance, but to "open" an existing Form.
In that case there are two alternatives:
a. the Form instance is already open, and is visible: your done.
Whether an instance of a Form is visible, or hidden, it's in the Application.OpenForms collection. Note that the collection has a very limited set of operators: you can't use something like 'Contains. And, each Form in that collection is in a "vanilla" type-form: you can't automatically assign it to a variable of the type of FormX: you have to cast the result to ProjectName.FormX.
b. the Form instance is now hidden: your job is to 'Show it.
So, now you can define the alternatives here clearly: based on whether, as Eddie was pointing out, the "string" you have contains a Class Name of a Form, or the string contains the name of a form already created as an instance.
You can use Brandelero's code to create a new instance, if that's what you want, and it doesn't matter to you if there already any other instances of the Type that exist.
And, if you want to create an instance only if an instance does not already exist, or you just want to make sure an existing instance is visible: you can mess around with the Application.OpenForms collection to see what's what.
Let's look at simple test case:
// in Form scopeprivate Form2 newForm2 = new Form2();
private Form2 newForm2a = new Form2();
// in Form Load event
newForm2.Name = "newForm2";
newForm2a.Name = "newForm2a";
foreach (Form theCandidateForm in Application.OpenForms)
if (theCandidateForm.Name == "newForm2")
// you found a match by Name
Console.WriteLine("Found match by Name: " + theCandidateForm.Name);
if( theCandidateForm.GetType() == newForm2.GetType())
// you found one, of perhaps more than one, instance of 'newForm2
Console.WriteLine("Found match by Type " + theCandidateForm.Name);
The output of this in the VS 'Output window would be:
Found match by Name: newForm2
Found match by Type newForm2
Found match by Type newForm2a
I hope this information adds something to this thread.
“This isn't right; this isn't even wrong." Wolfgang Pauli, commenting on a physics paper submitted for a journal
If I throw the exception in the catch block does the finally ever execute? Reason why I am doing this is because the DLL's do not perform logging, the calling class does. But I need to make sure I dispose of my objects.